Protal 7900HT is a VOC free,100% solids, 2 part epoxy coating for pipelines operating at higher temperatures. It is a high build liquid coating that...
Protal 7900HT is a VOC free,100% solids, 2 part epoxy coating for pipelines operating at higher temperatures. It is a high build liquid coating that is spray applied in one coat in the field or shop. It cures fast to allow quick backfill when applied to hot pipe.
Can be used in a wide variety of spray applications using Protal Liquid Coatings. It is designed for use where fast and easy setup, no...
| Can be used in a wide variety of spray applications using Protal Liquid Coatings. It is designed for use where fast and easy setup, no clean up, minimal material waste and minimal equipment maintenance is needed. 3:1 |
Available accessories:
Denso Protal 7200 Cartridge (1000ml)
Denso Protal 7900 HT Cartridge (1000ml)
Denso Protal Air Cartridge Gun (1000ml) – Mixing Tip/Straight
Denso Protal Air Cartridge Gun (1000ml) – Mixing Tip/Right Angle
The Denso Quick Lock Adapter is an accessory for the Denso Protal Air Cartridge 1000ml Gun which connects the gun to the cartridges....
The Denso Quick Lock Adapter is an accessory for the Denso Protal Air Cartridge 1000ml Gun which connects the gun to the cartridges.
Denso Protal Applicator Pads are designed to apply Protal 7200, 7125, 7300, and 7900 to your pipeline. Protal should be applied to the specified Dry...
Denso Protal Applicator Pads are designed to apply Protal 7200, 7125, 7300, and 7900 to your pipeline. Protal should be applied to the specified Dry Film Thickness (DFT) using a Denso applicator pad. Wet film measurements are to be performed to ensure close adherence to the thickness specification. Apply the product onto the surface and spread down and around the surface in bands beginning from the leading edge of the material to as far under the pipe as can be reached. Overlap the bands and onto the existing coating a minimum of 1″ (25 mm).
Protal ARO is a VOC free, 100% solids liquid epoxy coating formulated to be applied over FBE as an ARO coating (abrasion resistant overlay). It...
Protal ARO is a VOC free, 100% solids liquid epoxy coating formulated to be applied over FBE as an ARO coating (abrasion resistant overlay). It is a 3:1 ratio compatible for most plural component spray units coating that can be spray or hand applied in the field or shop. Protal ARO is used to protect FBE mainline coatings and over Protal 7200 on girth welds during directional drilling, bores, river crossings and other rough terrain applications. Protal ARO can be used to provide additional protection to the coating on bends, fittings and fabrication when severe handling or rough terrain persist.
A fast drying surface tolerant epoxy coating that can be hand or spray applied to wire brushed rusty steel surfaces. Used for above and below...
A fast drying surface tolerant epoxy coating that can be hand or spray applied to wire brushed rusty steel surfaces. Used for above and below ground pipelines, structural steel, bridges, tanks, and other steel surfaces.
Canusa’s Repair Products are used to repair and/or fill voids in damaged coatings. A full line of products provides the flexibility to make a variety...
Canusa’s Repair Products are used to repair and/or fill voids in damaged coatings. A full line of products provides the flexibility to make a variety of repairs to mainline or field joint coatings, ranging from minor coating damage to exposed steel. All of Canusa’s Pipeline Repair Products offer flexibility of installation, exhibit excellent adhesion to steel and are compatible with all common pipeline coatings. These products also remain permanently flexible and provide superior resistance to moisture infiltration, resulting in complete corrosion protection.
2880 Bergey Road, Suite F, Hatfield, PA 19440
Phone: (877) 373-0118 | Fax: (888) 850-3787
Western PA Location: 500 Alpha Drive, Canonsburg, PA 15317