Epi-Seal Seam Sealer is a two component, fiberglass reinforced epoxy resin system for high effciency repairs on all riveted, bolted or welded tank or vat...
Epi-Seal Seam Sealer is a two component, fiberglass reinforced epoxy resin system for high effciency repairs on all riveted, bolted or welded tank or vat seams.
Available in 1 LB or 2 LB Kits: 12 Kits per Case
Provides an extremely tough, inexpensive casing insulator that electrically isolates a gas carrier main from a steel casing, and provides excellent abrasion control....
Provides an extremely tough, inexpensive casing insulator that electrically isolates a gas carrier main from a steel casing, and provides excellent abrasion control.
FRP Flatties are made of a select combination of random glass mat reinforcements saturated with polyester resins combined with suitable fillers. These composites are cured...
FRP Flatties are made of a select combination of random glass mat reinforcements saturated with polyester resins combined with suitable fillers. These composites are cured and compressed under moderate pressure to form smooth, dense laminates. Standard sizes include 12″x12″ square, 6″x12″, 3’x6′ sheets, and 4’x8′. FRP Flatties are available off the shelf in 1/16″, 1/8″, 1/4″ and 1/2″ thickness.
An extremely strong, non-conductive fiberglass reinforced plastic insulation spacer, with a peripheral circumference of 120°, minimizes shielding effect on cathodic protection systems. •Used by utilities...
An extremely strong, non-conductive fiberglass reinforced plastic insulation spacer, with a peripheral circumference of 120°, minimizes shielding effect on cathodic protection systems.
•Used by utilities to prevent and/or correct electrical shorts caused when buried steel mains contact each other or are in close proximity.
•The 120° peripheral circumference minimizes any possible shielding effect on the pipes cathodic protection systems.
•For most applications, FRP Spacers offer superior physical properties over other plastics and rubber such as PVC and polyethylene.
•The superior compressive strength of FRP over other non-conductive materials is necessary due to the point loading nature of contact shorts.
•FRP spacers will not cold flow, will not become brittle in cold temperatures and will not soften or distort from heat.
A non-corrosive, non-conductive 180° pipe saddle fabricated from high quality FRP that protects pipe insulation and pipe systems from abrasive wear at overhead hangers and...
A non-corrosive, non-conductive 180° pipe saddle fabricated from high quality FRP that protects pipe insulation and pipe systems from abrasive wear at overhead hangers and supports.
A non-conductive, pre-shaped 240° peripheral snap-on pipe saddle. FRP roll-on shields will never corrode or deteriorate, physically or chemically, and are easily installed. •Used by...
A non-conductive, pre-shaped 240° peripheral snap-on pipe saddle. FRP roll-on shields will never corrode or deteriorate, physically or chemically, and are easily installed.
•Used by utilities for electrical isolation and abrasion control of mains and by industry for load distribution, energy conservation, and insulation protection at hangers and supports of over head and pylon-supported pipe mains.
•Employed for abrasion control on plastic pipe systems and wrapped cables.
•Substitute for, or use in place of metal saddles where electrical insulation is desirable.
•Ideal for pipes exposed to corrosive environments.
•Protects pipe insulation and plastic pipe systems from abrasive wear at overhead hangers and supports.
•May be banded, cemented or taped into place.
•Special lengths can be made available.
•Oversized shields and saddles are used over bridge mains that have had protective tape applied, resulting in an increased outside diameter of the pipe and without damaging the tape.
2880 Bergey Road, Suite F, Hatfield, PA 19440
Phone: (877) 373-0118 | Fax: (888) 850-3787
Additional Location: 19 West Maiden Street, Washington, PA 15301