Categories

Shop

Featured

Barlow Flange Isolation Joint

The Barlow Flange Isolation Joint is welded into place for a permanent solution and designed to the highest possible standards using precision machined heavy duty...

Read more

The Barlow Flange Isolation Joint is welded into place for a permanent solution and designed to the highest possible standards using precision machined heavy duty components.

FEATURES:

•  Thicker dielectric sleeves (1/8″) machined to precise, close tolerance dimensions, both length and diameter

•  Flange bolt holes line reamed to provide perfect alignment and close tolerance fit to the dielectric sleeves

•  Flange studs machined from Alloy Steel and heat treated to ASTM Designation A-193-52T Grade B-7 resulting in superior strength and greater resistance to stress-induced elongation

•  Coupling nuts machined from Alloy Steel and heat treated to ASTM Designation A-194 Class 2-H

•  Precision machined steel washers, flat, parallel and counterbored allowing for square alignment and clearance for the dielectric sleeves

•  Flange gasket precision cut for ideal fit with small projection into the stream to prevent bridging of the joint inside the pipe

•  Precise assembly with accurate torquing carried out in sequential pattern followed by retorquing after 24 hours

•  Flange gap sealed with epoxy resin to prevent contamination and electrical shorting

•  Dielectric strength test (minimum) 5 kV at 50 hz for 1 minute (dry air)

 

Read less

Add to Quote

Black Beauty Medium Grit 50lb Bags

BLack Beauty MEDIUM Grit: For general purpose repair and maintenance blasting for the removal of paint and rust, structural steel, mill scale, and aggregate exposure. Features...

Read more

BLack Beauty MEDIUM Grit: For general purpose repair and maintenance blasting for the removal of paint and rust, structural steel, mill scale, and aggregate exposure.

Features & Benefits
• Less than 0.1% free silica
• Hard angular particles
• Uniform density
• Low friability
• Low dusting
• Chemically inert
• Passes 40CFR 261.a (TCLP)
• Passes California Title 17 (CARB) (selected certified plants)
• QPL Approved: MIL-A-2262B(SH) (selected plants only) SSPC AB-1 (all plants)

Read less

Add to Quote

BÖHMER Ball Valves

DESIGN BÖHMER fully welded ball valves meet the requirements of the most common national and international standards. FIRE PROTECTION When fire safe certification is required, BÖHMER can produce...

Read more

DESIGN

BÖHMER fully welded ball valves meet the requirements of the most common national and international standards.

FIRE PROTECTION

When fire safe certification is required, BÖHMER can produce a range of valves to API 6FA, API 607 and BS 6755 P 2.

TRUNNION MOUNTED BALL

The standard design of BÖHMER ball valves provides a trunnion mounted ball for pressure class ANSI150 starting at 6 inch and ANSI300 and above at 3 inch size. The maintenance-free bearings for stem and trunnion are self-lubricating, thus assuring a lower torque especially for high pressure ratings.

ANTI-STATIC DEVICE

When required, the ball valve design includes an electric conductive connection between the internal parts of the ball valve and the body providing the anti-static function.

STEM SEALING

The sealing of the stem to the atmosphere is achieved by up to three independent sealing systems. The stem sealing design ensures the anti-blow-out function. Some valves can be produced with a design of the stem assembly, so the seals are replaceable under full pressure in either open or closed position.

EMERGENCY SEALING

As an option, BÖHMER ball valves can be delivered with an additional emergency sealing injection for the seat-rings and/or stem sealing.

Read less

Add to Quote

Borin Stelth 2 Reference Electrode SRE-007-CUY

Borin Stelth 2 Solid-State Reference Electrode for Buried and Concrete Service Model SRE-007-CUY Copper-Copper Sulfate (Cu-CuSO4) For direct burial and concrete in chloride-free conditions. Size:...

Read more

Borin Stelth 2 Solid-State Reference Electrode for Buried and Concrete Service
Model SRE-007-CUY Copper-Copper Sulfate (Cu-CuSO4) For direct burial and concrete in chloride-free conditions.

Size: 1.5″ (40 mm) diameter x 7″ (180 mm) long. Lead Wire: 50′ (15 m) or 20′ (6 m) of #14 (2.5 mm2) RHH-RHW wire. Stability: ±5 millivolts.
Material: Ceramic with moisture retention membrane.
Working Temperature Range: 32° F to 176° F (0° C to 80° C).
Material Temperature Range: -60° F to 185° F (-51° C to 85° C).

Read less

Add to Quote

Brackets

Gas Meter brackets are typically used to support gas meter service installations in residential, commercial and industrial applications. A wide range of gas meter brackets...

Read more

Gas Meter brackets are typically used to support gas meter service installations in residential, commercial and industrial applications. A wide range of gas meter brackets are available that not only make installations easier, but also offer safety and durability benefits.

Gas Meter Bracket Features:

• Wide variety of designs for foundation or remote installations
• Standoffs ranging from 4” to 12”
• Fixed and adjustable styles available
• Custom designs for your specific application needs

Read less

Add to Quote

Bristle Blaster® – Cordless

The Bristle Blaster® System is an innovative bristle blasting process that removes corrosion and generates an anchor profile by using a specially designed rotary bristle...

Read more

The Bristle Blaster® System is an innovative bristle blasting process that removes corrosion and generates an anchor profile by using a specially designed rotary bristle tool. This tool consists of hardened wire bristle tips that are bent forward and are dynamically tuned to a hand-held, battery operated, power tool which operates at approximately 2,300 rpm. Most common uses include: coating removal, paint removal, scale removal, weld cleaning, aurface decontamination, aurface preparation, texturing applications, and corrosion removal.

Please click here to view a video on how to operate a non-cordless Bristle Blaster®

KIT INCLUDES:

(1) – Cordless Drive Unit,  (1) Adaptor 23mm, (5) – Carbon Steel Bristle Belts 23mm, (1) Accelerator Bar,  (1) Charger, (1) 18V/8.0 Ah battery that should last up to 0.5m2 per full charge.

Read less

Add to Quote

Bristle Blaster® – Double

Double the power! The Electric Bristle Blaster® Double uses two 23mm belts with a productivity rate of approximately 3m2/hr. 910 Watt maximum output with 2,300...

Read more

Double the power! The Electric Bristle Blaster® Double uses two 23mm belts with a productivity rate of approximately 3m2/hr. 910 Watt maximum output with 2,300 rpm Free Speed (± 5%).

The Bristle Blaster® System is an innovative bristle blasting process that removes corrosion and generates an anchor profile by using a specially designed rotary bristle tool. This tool consists of hardened wire bristle tips that are bent forward and are dynamically tuned to a hand-held power. Most common uses include: coating removal, paint removal, scale removal, weld cleaning, surface decontamination, surface preparation, texturing applications, and corrosion removal.

Please click here to view a video on how to operate the Bristle Blaster®

Bristle Blaster® Electric Double Kit includes:  (1) – 110V Electric Drive Unit,  (1) Adaptor 23mm, (6) – Carbon Steel Bristle Belt 23mm, (1) Accelerator Bar

Read less

Add to Quote

Bristle Blaster® – Electric Kit

The Bristle Blaster® System is an innovative bristle blasting process that removes corrosion and generates an anchor profile by using a specially designed rotary bristle...

Read more

The Bristle Blaster® System is an innovative bristle blasting process that removes corrosion and generates an anchor profile by using a specially designed rotary bristle tool. This tool consists of hardened wire bristle tips that are bent forward and are dynamically tuned to a hand-held power tool which operates at approximately 3,200 rpm. Most common uses include: coating removal, paint removal, scale removal, weld cleaning, surface decontamination, surface preparation, texturing applications, and corrosion removal.

Please click here to view a video on how to operate the Bristle Blaster®

KIT INCLUDES:

SE-660-02 & SE-1160-BMC CARBON SPRING STEEL – 11 & 23 mm Belts –  Bristle Blaster Electric Kit includes:  (1) 110V Electric Drive Unit,  (1) each – Adaptor 23mm & 11mm,  (5) each of the Carbon Steel Bristle Belt 23mm &11mm, (1) Accelerator Bar 23mm & (1) Accelerator Bar 11mm(13 lbs)

SE-667-02 & SE-1160-BMC CARBON SPRING STEEL – 23mm Belts – Bristle Blaster Electric Kit includes:  (1) 110V Electric Drive Unit,  (1) Adaptor 23mm, (10) – Carbon Steel Bristle Belt 23mm, (1) Accelerator Bar  (13 lbs)

Read less

Add to Quote

Bristle Blaster® – Pneumatic Kit

The Bristle Blaster® System is an innovative bristle blasting process that removes corrosion and generates an anchor profile by using a specially designed rotary bristle...

Read more

The Bristle Blaster® System is an innovative bristle blasting process that removes corrosion and generates an anchor profile by using a specially designed rotary bristle tool. This tool consists of hardened wire bristle tips that are bent forward and are dynamically tuned to a hand-held power tool which operates at approximately 3,500 rpm. Most common uses include: coating removal, paint removal, scale removal, weld cleaning, surface decontamination, surface preparation, texturing applications, and corrosion removal.

Please click here to view a video on how to operate the Bristle Blaster®

KIT INCLUDES:

SP-647-02 CARBON SPRING STEEL – 11 & 23 mm Belts – Bristle Blaster Pneumatic Kit includes: (1) Pneumatic drive unit, (2) adaptors 11mm & 23mm, (5) carbon steel Bristle Belt 11mm, (5) carbon steel Bristle belt 23mm, (2) MBX In-line Air Pressure Regulators 11mm & 23mm, (1) dust exhaust system, (1) Accelerator Bar 11mm & (1) Accelerator Bar 23mm

SP-649-02 STAINLESS STEEL – 11 & 23 mm Belts – Bristle Blaster Pneumatic Kit includes: (1) Pneumatic drive unit, (2) adaptors 11 & 23mm, (5) stainless steel Bristle Belt 11mm, (5) stainless steel Bristle belt 23mm, (2) MBX In-line Air Pressure Regulators 11mm & 23mm, (1) dust exhaust system, (1) Accelerator Bar 11mm & (1) Accelerator Bar 23mm

Read less

Add to Quote

Bristle Blaster® Belts

Bristle Blaster® Belts consist of a high performance polyamide fabric. The U-shaped bristles made of carbon spring steel or of stainless steel are anchored in the...

Read more

Bristle Blaster® Belts consist of a high performance polyamide fabric. The U-shaped bristles made of carbon spring steel or of stainless steel are anchored in the belt. The Bristle Blaster® belts are highly flexible which ensures a high level of safety and a long service life.

Bristle Blaster® Belt 23 mm (carbon spring steel) – 0.7 mm carbon spring steel wire, tips angled and sharpened.

Bristle Blaster® Belt 11 mm (carbon spring steel) – 0.7 mm carbon spring steel wire, tips angled and sharpened.  Designed for difficult to reach areas (90° angles, fillet welds).

Bristle Blaster® Belt 23 mm (stainless steel) – 0.7 mm stainless steel wire, tips angled and sharpened.

Bristle Blaster® Belt 11 mm (stainless steel) – 0.7 mm stainless steel wire, tips angled and sharpened.  Designed for difficult to reach areas (90° angles, fillet welds).

Read less

Add to Quote

Search

Shopping cart

Cart

Have Questions?

Call 877-373-0118 to speak with a product specialist.

or

Click here to send a message.